The Honda Indy V8 engine is a 3.5-litre naturally-aspirated V8, developed and produced by HPD-AHM Co. under a support from Ilmor Engineering for IndyCar Series. Honda Indy V8 was a highly-successful IndyCar Series engine supplier from 2003 to 2011 seasons before replaced by Honda Indy V6 at the following season. Honda Indy V8 was unveiled at 2002 Detroit Auto Show and assembled at HPD power assembly plant in Santa Clarita, California, USA in early 2003.
Maps, Directions, and Place Reviews
1st Generation (2003-2004)
Honda debuted IndyCar Series as engine supplier in 2003 season after a CART successful era. Developed by Ilmor and designated as HI3R, engine's capacity was 3.5-liter. Honda supplied Andretti Green Racing, Team Rahal, Fernández Racing and Access Motorsports teams. Honda's 2003 stats were 3 pole positions, 6 fastest laps and 2 wins. A revised engine named HI4R was used in 2004 until new regulations came into effect at the 2004 Indianapolis 500.
Applications
- Dallara IR3
- G-Force GF09
Honda Fit Indianapolis Video
2nd Generation (2004-2006)
Honda designed a new engine to address the 2004 IRL rule change which required reduced displacement. Developed once again by Ilmor and designated as HI4R-A, its capacity was 3.0-liter and debuted at the 2004 Indianapolis 500. With subsequent evolutions named HI5R and HI6R, Honda was clearly dominant engine, scoring 33 poles, 35 fastest laps, 41 wins totally in three seasons including 3 Indianapolis 500s. Since Chevrolet and Toyota leaves IndyCar Series after 2005 season, Honda won exclusive tender IndyCar Series engine supplier for 2006 to 2011 season.
Applications
- Dallara IR4
- Panoz GF09B
- Panoz PZ09C
3rd Generation (2007-2011)
This family was designed as a replacement for the HI6R but enlarged to better accommodate variable valve timing and Active Fuel Management while still generating good performance. HI7R-HI11R's capacity reverted to 3.5-liters respectively since 2007 season. HI7R-HI11R engine was developed and assembled by Honda in Santa Clarita, California, USA (Honda Performance Development's current headquarters) but under support from Ilmor Engineering for trackside support, engine arrangement, tune up and engine maintenance. HI7R-HI11R engine supplied for all IndyCar Series teams. HI7R-HI11R was highly-successful engine with 86 pole positions, fastest laps and wins respectively including 2008 Nikon Indy 300 exhibition race and 5 Indianapolis 500s. Due to the IndyCar Series chassis and engine development freeze beginning in 2008, IndyCar Series kept the Honda Indy V8 3rd generation model until 2011 season for cost reasons.
During that time, since the IndyCar Series had only one engine manufacturer, Honda focused on minimizing engine failure and minimizing costs instead of defeating rivals. As such, the engines were moderately de-tuned. The engines proved themselves to be quite durable. There had been no engine failures at Indy from 2006 to 2010, which also lowered the number of crashes. Most of the engines, including those used for the Indy 500, were used for multiple races and were intended to last 1,200 miles (1,931 kilometers) between rebuilds. The Honda engines were only available via lease arrangement from Honda, which, for the 2010 full season, cost $935,000 U.S. per season, per car.
The HI7R-HI11R were rev-limited to 10,300 rpm and produced approximately 650 hp. The valve train is a dual overhead camshaft configuration with four valves per cylinder. The crankshaft is made of alloy steel, with five main bearing caps. The pistons are forged aluminum alloy, while the connecting rods are machined alloy steel. The electronic engine management system is supplied by Motorola, firing a CDI ignition system. The engine lubrication is a dry sump type, cooled by a single water pump.
Year 2011 final specifications
- Engine type: Normally aspirated, fuel-injected, aluminum alloy 90-degree V-8
- Displacement: 3.5 litres (213.6 cubic inches)
- Valve train: Dual overhead camshaft, four valves per cylinder, finger-follower actuated coil spring/valve assembly
- Crankshaft: Steel alloy, five main bearings
- Pistons: Billet aluminum alloy
- Connecting rods: Machined steel alloy
- Engine management: McLaren Electronics Engine Control Unit (ECU) with engine strategies by Honda Performance Development
- Ignition system: Digital inductive
- Injection system: Single injector per cylinder, fed by an engine-driven mechanical fuel pump
- Cooling: Single mechanical water pump feeding a single-sided cooling system
- Transmission: Six-speed sequential, paddle-operated
- Fuel: Sunoco 100% fuel-grade ethanol
- Weight: 275 lbs. (124.7 kg.)
Applications
- Dallara IR5
Honours
On February 10, 2012 Honda Indy V8 was honoured as "North American Race Engine of the Year" by Race Engine Magazine.
Source of the article : Wikipedia
EmoticonEmoticon